A wall can feel dry to the touch in a day while the studs and plates behind it stay wet enough to feed mold. Call Water Heater Repairer and we route you to an independent drying contractor in Savannah who measures, maps and logs moisture until the structure reaches its drying goal.
Proper drying is applied psychrometrics, and it has little in common with leaving fans running for a weekend.
Every contractor we route to in Savannah is an independent, licensed and insured business. Plenty hold IICRC water restoration training; ask to see it at the door.
Drying is a race against wicking, so we prioritize contractors with dehumidifiers and air movers already loaded. Arrival is often within the hour depending on location and demand.
Before the first fan spins, the contractor writes up the drying plan, the equipment count and the rate structure. That written scope heads off disputes over equipment days later.
Pin and pinless moisture meters, thermo-hygrometers and thermal imaging cameras are the core kit. Those tools turn a guess into a dated moisture map.
The most common call we take sounds like this: the leak was fixed, the carpet feels dry, so why does the room smell musty a week later? Almost every time, the moisture is still sitting in the bottom plate, inside the wall cavity, or in the subfloor beneath the pad. That is exactly what a structural drying contractor is there to find and remove.
We also hear from people worried about the noise and the power bill. A typical setup runs several air movers and one or two dehumidifiers around the clock, and the contractor should check circuit loads before plugging everything in. Running it right for a few days costs far less than replacing cupped flooring, delaminated cabinets or moldy drywall later.
Every job opens with a moisture map and closes only when all readings reach target.
First, the pro reads a dry standard off unaffected materials elsewhere in the house. That number, close to the material's equilibrium moisture content, becomes the drying goal for every wet area.
LGR dehumidifiers pull water out of warm, damp air down to low grains per pound. In cold basements or dense materials, a desiccant dehumidifier keeps working where refrigerant coils stall.
Axial fans move big volumes over open floors; centrifugal units aim tight, fast air along wall bases and under cabinets. Every unit goes where the moisture map says, not where it fits.
Instead of tearing out drywall, many contractors pull the baseboard and drill small holes into the cavity behind it. An injection system pushes dry air through hoses into each stud bay, and the trim hides the holes afterward.
Hardwood cups when the undersides take on water and swell ahead of the surface. Sealed drying mats or panels draw moisture up through the wood with steady suction.
In a closed chamber, plastic sheeting walls off the wet area so equipment conditions a smaller volume of air. It dries faster and keeps the noise and electrical load out of the rooms you are living in.
Here is what a properly run drying job looks like from start to finish.
Tell us where the water came from, how long it sat and which rooms are affected. Those answers tell us whether you need drying only or extraction first, and we route the right contractor.
The pro shows up carrying meters, a thermal imager and a starting set of dehumidifiers and fans. Thermal imaging traces how far water has wicked up walls before anything gets moved.
You get a written scope: evaporation class, drying goals, equipment count, expected days and how billing works. No equipment starts until you sign off on it.
Daily visits record readings, shift equipment and remove units as each area hits target. The final drying log, with every reading dated, is yours for the insurance file.
Fans by themselves just stir humid air around; they do not take the water out. As relative humidity rises, vapor pressure in the room catches up to the wet material and drying stalls. If nobody is controlling grains per pound, the studs and subfloor can sit wet for weeks.
| Evaporation class | What it usually means |
|---|---|
| Class 1 | Limited wetting, low-porosity materials |
| Class 2 | Whole room, carpet and pad wet, wicking under two feet |
| Class 3 | Overhead water that soaked ceilings, insulation and walls |
| Class 4 | Dense materials like hardwood, plaster or concrete holding bound water |
Have an independent drying pro near Savannah take readings today.
Our dishwasher leaked overnight and the kitchen floor looked fine by lunch. The drying contractor found the oak reading way above a dry board in the hallway and set up panels on it. It ran five days, and the boards stayed flat.
The insurance adjuster tried to knock two days of equipment off the claim. I forwarded the daily drying log with readings for each wall, and the claim went through as written. Those dated readings ended the argument fast.
A supply line burst in our office on a Friday and soaked three rooms. Instead of tearing out walls, the crew pulled baseboards and fed dry air into the cavities through small holes. They tented off the wet rooms, so the front office stayed open.
Our basement got wet after a water heater let go, and we ran fans for a week. The smell would not go away, so we called and the pro scanned the walls with a thermal camera. Water had wicked up behind the paneling almost two feet. A desiccant unit and a few days of readings finally got it dry.
A typical Class 2 job hits goal in about three to five days. Dense materials like hardwood, plaster or concrete often run longer since the water sits deeper. The moisture readings decide when units get pulled, not a set number of days.
Each wet wall is measured against a dry standard read from untouched drywall elsewhere in the house. Once the numbers match that baseline, that wall is done.
Often they do not. For clean water in open stud bays, drilling behind the baseboard and injecting dry air often saves the wall. Wet insulation, contaminated water or mold growth usually means a flood cut.
Shutting them off at night lets the air get damp again and undoes part of the progress. Ask the contractor about a closed drying chamber, which confines the noise and power draw to the wet area.
An LGR unit uses refrigerant coils and works best in warm, occupied spaces. Desiccant units use a moisture-absorbing wheel and keep pulling water in cold spaces or from dense materials.
Fast drying gives the boards the best chance to settle back flat. Some mild cupping relaxes as moisture equalizes, so the contractor will usually recommend waiting before anyone sands.
Drying calls get routed to contractors across Savannah and the surrounding suburbs, including 76227. From downtown condos to split-levels on the edge of town, the approach stays the same: measure, map, dry and document.
Plaster walls and old-growth hardwood hold water longer and usually need desiccant drying.
Water moves through shared walls, so mapping often covers the unit next door too.
Slab homes and finished basements around Savannah get the same readings-first approach.
Supply line, water heater, upstairs tub: whatever the source, earlier calls mean less wicking. Every hour of delay lets water climb higher into drywall and deeper into framing.
Call +1-877-637-9008
